Deck preparation
Old roofing is removed and the deck is repaired before new layers go down.
Flat Roofing
Rubber Roof Installation Chester, NJ
A Chester roofer who installs EPDM can put a new rubber roof on a flat or low slope section of almost any home, so the roof handles sun, cold and storms for decades. Dial (908) 955-2098 to talk with a local roofer about a new rubber roof.
EPDM is the material most people mean when they say rubber roof. The membrane is thick, stretchy rubber that tolerates temperature swings and resists hail and sunlight well. Unlike TPO and PVC, its seams are taped rather than heat welded.
The first decision is how the membrane is held down. Fully adhered roofs bond the whole sheet to the cover board with adhesive, mechanically attached roofs use plates and fasteners along the seams and ballasted roofs hold a loose sheet down with river stone. Residential roofs are most often fully adhered.
Thickness and color are the next choices. Sixty mil EPDM costs a little more than 45 mil but resists punctures better and lasts longer. Black is standard and holds heat, while white reflects it. Where the rubber meets a shingled roof or the house wall, the tie-in detail matters as much as any of these choices.
Rubber Roof Installation is often paired with rubber roof repair and flat roof installation, depending on the cause.
Need rubber roof installation in Chester? Call (908) 955-2098 to reach a nearby roofing contractor.
Call nowThe process
How rubber roof installation works
Each layer is set up to give the membrane a smooth, solid base.
Prepare the deck
The roofer checks the deck for rot, gaps and loose sheets and confirms the roof has enough slope to drain. Old roofing is removed if the roof is being replaced.
Install insulation
Polyiso insulation and a cover board create a flat, firm base for the rubber. Slope can be built in at this stage.
Roll out the membrane
The EPDM is unrolled, positioned and left to relax so wrinkles flatten before any adhesive goes on. Laps are arranged so water flows over them.
Adhering
Half the sheet is folded back, adhesive is applied to both surfaces and the rubber is pressed into place. Each half gets the same treatment in turn. Brooming from the middle outward pushes trapped air to the edges.
Seal the seams
Primer and seam tape join the sheets, with T-joints covered by extra patches. Tape edges are finished with lap sealant.
Finish the edges
Perimeter edge metal, wall flashing and pipe boots complete the roof. Termination bar and counter flashing seal the wall edge. Before the crew leaves, seams are probed for any loose spots.
What is included
What goes into a rubber roof
Edge metal
Walls, curbs, pipes and edges are flashed for a finished roof.
Cover board
A cover board protects the insulation for a smooth surface.
Seam tape
Seams are primed, taped and rolled and is checked before closeout.
Rubber sheet
Wide sheets of EPDM cover the roof over a clean, dry base.
Related service
EPDM Roof Installation Chester, NJ
Installing EPDM well comes down to preparation, seams and flashing. The membrane has to lie flat on a clean, dry cover board, the adhesive has to reach the right tack before the sheet is laid and every seam has to be primed and rolled with care. Dry, mild days give the best bond. Different adhesives may be used in the field and at the flashings, each matched to the job it does.
A good Chester installer also plans for movement. Securing the membrane at the edges and flashing corners correctly prevents later tears. Ask about edge securement before work starts.
Local help
Rubber Roof Installation Near Me
In Chester, EPDM is a popular choice for low slope roofs on additions and attached garages. Homes in Chester and nearby places including Flanders, Succasunna, Mendham and Budd Lake benefit from rubber roofing because it flexes with the seasons, which is why the seams and flashing deserve careful attention.
Searching for rubber roof installation near me from Chester or Flanders, Succasunna, Mendham and Budd Lake? Call (908) 955-2098 to talk to a roofer who works in your part of town.
How the weather here affects roofs around Chester
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Chester is busiest after a hard winter and before the next one.
Why call
Why act early
Less damage
Small roof problems caught early usually stay small repairs.
Local knowledge
Roofers in Chester know the roof types and weather wear common in local homes.
Straight answers
Ask the roofer about the cause, the options and the estimate before work starts.
Common questions about rubber roof installation
How thick should a rubber roof be?
The common choices are 45 mil and 60 mil. The thicker sheet holds up better to traffic and weather. Heavy duty options exist too.
What is the difference between EPDM and TPO?
They are related but not the same. EPDM is usually black, very flexible and seamed with tape, while TPO is usually white, more reflective and heat welded at the seams. A roofer can help you choose.
Should my rubber roof be black or white?
Color affects heat gain. Black holds heat and white reflects it. Ask about both options.
How long does a new rubber roof last?
A properly installed EPDM roof commonly lasts 20 to 30 years or more. Good seams, drainage and occasional checks make the difference. Patching EPDM is straightforward.
Is it possible to install EPDM over the old roof?
Recovering depends on the condition of the old roof. The old roof must be a single dry layer, with a recover board over it. If the old roof is wet, it must come off. The roofer tests the old roof for moisture before recommending a recover.
More questions? Call (908) 955-2098
Other services that may help
Rubber Roof Repair
EPDM rubber roof repairs done with primer, cover tape and lap sealant made for rubber, so the membrane seals again without a tear-off.
Learn moreFlat Roof Installation
Installing TPO, PVC, EPDM or modified bitumen roofs on additions, garages, porches and flat-roof homes, planned around how the roof will be used.
Learn moreTPO Roofing
Heat-welded TPO membrane for flat and low-slope roofs, sized to the deck, the drains and the way the roof is used.
Learn moreFlat Roof Replacement
Tearing off or recovering a worn flat roof and installing a new membrane, insulation and edge metal, with tapered insulation where water used to sit.
Learn more
Looking for something else?
See all roofing servicesNeed rubber roof installation in Chester, NJ?
Call (908) 955-2098 to talk to a roofer serving Chester, NJ.